central locking
#1
central locking
drivers side door lock not working, locks but will not unlock using the internal or outside handles. Only way to unlock is to use the emergency key.
Fault codes shown
00928 lock module front drivers side (F220) impulse signal.
00932 window motor drivers side (V147) incorrect basic setting
01811 power supply to control unit (J386)drivers door.
Fault codes shown
00928 lock module front drivers side (F220) impulse signal.
00932 window motor drivers side (V147) incorrect basic setting
01811 power supply to control unit (J386)drivers door.
#2
drivers side door lock not working, locks but will not unlock using the internal or outside handles. Only way to unlock is to use the emergency key.
Fault codes shown
00928 lock module front drivers side (F220) impulse signal.
00932 window motor drivers side (V147) incorrect basic setting
01811 power supply to control unit (J386)drivers door.
Fault codes shown
00928 lock module front drivers side (F220) impulse signal.
00932 window motor drivers side (V147) incorrect basic setting
01811 power supply to control unit (J386)drivers door.
VAG Error Code: 00928
Fault Location:
Locking Module for Central Locking: Front Drivers Side (F220) - Implausible Signal
Possible Cause:
Door Locks not working properly.
Wiring/Connector(s) from/to Locking Module for Central Locking: Front Driver Side (F220) faulty.
Voltage Supply for Locking Module for Central Locking: Front Driver Side (F220) faulty.
Door Lock Mechanics are stiff/partially seized.
Locking Module for Central Locking: Front Driver Side (F220) faulty.
Possible Solutions:
Check/Replace Wiring/Connector(s) from/to Locking Module for Central Locking: Front Driver Side (F220).
Read Measuring Value Blocks (MVB)
Check voltage supply to driver's door control unit or to door main connector (lower left footwell).
Check Door Lock Mechanics/Operation.
Check Locking Module for Central Locking: Front Driver Side (F220).
VAG Error Code: 00932
Fault Location:
Electric Window Motor: Drivers Side (V147) - No or Incorrect Basic Setting/Adaptation/Adjustment
Possible Cause:
Window Automatic Run not working.
Pinch Protection limited.
Automatic Run & Pinch Protection not adapted.
Incorrect Window Motor/Door control module installed.
Possible Solutions:
Adapt Automatic Run & Pinch Protection (see Special Notes).
Verify the correct Window Motor(s)/Door control module(s) are installed.
Special Notes:
Pinch Protection Adaptation.
Make sure the window in question is completely closed.
Use the driver door window buttons to operate the window(s).
Roll down the window and keep holding the button down for 2 additional seconds after the window is already fully opened.
Roll up the window and keep holding the button up for 2 additional seconds after the window is already fully closed.
Now test the window automatic.
VAG Error Code: 01811
Fault Location:
Supply Voltage for Door Controller: Drivers Side (J386) - Lower Limit Exceeded/Faulty
Possible Cause:
Door Controller Functionality limited.
Window Regulator not working.
Fuse(s).
Wiring/Connector(s).
Door Controller: Drivers Side (J389).
Possible Solutions:
Check/Replace Fuse(s).
Check Wiring and/or Connector(s) from/to Door Controller: Drivers Side (J389).
Read Measuring Value Blocks (MVB).
Check Door Controller: Drivers Side (J389).
Fault Location:
Locking Module for Central Locking: Front Drivers Side (F220) - Implausible Signal
Possible Cause:
Door Locks not working properly.
Wiring/Connector(s) from/to Locking Module for Central Locking: Front Driver Side (F220) faulty.
Voltage Supply for Locking Module for Central Locking: Front Driver Side (F220) faulty.
Door Lock Mechanics are stiff/partially seized.
Locking Module for Central Locking: Front Driver Side (F220) faulty.
Possible Solutions:
Check/Replace Wiring/Connector(s) from/to Locking Module for Central Locking: Front Driver Side (F220).
Read Measuring Value Blocks (MVB)
Check voltage supply to driver's door control unit or to door main connector (lower left footwell).
Check Door Lock Mechanics/Operation.
Check Locking Module for Central Locking: Front Driver Side (F220).
VAG Error Code: 00932
Fault Location:
Electric Window Motor: Drivers Side (V147) - No or Incorrect Basic Setting/Adaptation/Adjustment
Possible Cause:
Window Automatic Run not working.
Pinch Protection limited.
Automatic Run & Pinch Protection not adapted.
Incorrect Window Motor/Door control module installed.
Possible Solutions:
Adapt Automatic Run & Pinch Protection (see Special Notes).
Verify the correct Window Motor(s)/Door control module(s) are installed.
Special Notes:
Pinch Protection Adaptation.
Make sure the window in question is completely closed.
Use the driver door window buttons to operate the window(s).
Roll down the window and keep holding the button down for 2 additional seconds after the window is already fully opened.
Roll up the window and keep holding the button up for 2 additional seconds after the window is already fully closed.
Now test the window automatic.
VAG Error Code: 01811
Fault Location:
Supply Voltage for Door Controller: Drivers Side (J386) - Lower Limit Exceeded/Faulty
Possible Cause:
Door Controller Functionality limited.
Window Regulator not working.
Fuse(s).
Wiring/Connector(s).
Door Controller: Drivers Side (J389).
Possible Solutions:
Check/Replace Fuse(s).
Check Wiring and/or Connector(s) from/to Door Controller: Drivers Side (J389).
Read Measuring Value Blocks (MVB).
Check Door Controller: Drivers Side (J389).
As taken from my new EOBD II Fault Codes Software
Thread
Thread Starter
Forum
Replies
Last Post
aidan
Volkswagen Vans - Routan, Sharan, Caddy, Transporter
1
01-16-2011 09:59 PM