no power to injectors 2005 MKIV 2.0 BEV
#2
Welcome to the forum.
VAG Error Code: 1658
As taken from my https://volkswagenforum.com/forum/ge...oftware-34973/
https://volkswagenforum.com/forum/ne...gnature-34185/
VAG Error Code: 16585
EOBD II Error Code: P0201
EOBD II Error Code: P0201
Fault Location:
Injector 1 (N30) - Circuit Malfunction/Open Circuit
Injector 1 (N30) - Circuit Malfunction/Open Circuit
Possible Cause:
Malfunction Indicator Lamp (MIL)(K83) active.
Lack/Loss of Power.
The engine may be harder to start.
Engine hesitation.
Malfunction Indicator Lamp (MIL)(K83) active.
Lack/Loss of Power.
The engine may be harder to start.
Engine hesitation.
Wiring/Connector(s).
Injector 1 (N30).
Engine Control Module (ECM).
Injector 1 (N30).
Engine Control Module (ECM).
Possible Solutions:
Check/Replace all faulty Wiring/Connector(s).
Read Measuring Value Blocks (MVB).
Low side signal current < 2.1 A.
Check/Replace all faulty Wiring/Connector(s).
Read Measuring Value Blocks (MVB).
Low side signal current < 2.1 A.
When is the code detected?:
The P0201 is set if the Engine Control Module (ECM) is detects a low or high voltage drop or resistance at the injector 1.
The P0201 is set if the Engine Control Module (ECM) is detects a low or high voltage drop or resistance at the injector 1.
Description:
Engine Control Module (ECM) checks the injectors circuit resistance and monitors the voltage drop during normal operation. The Engine Control Module (ECM) will trigger the P0201 code when the resistance or voltage drop at the injector 1 is out of specifications.
Engine Control Module (ECM) checks the injectors circuit resistance and monitors the voltage drop during normal operation. The Engine Control Module (ECM) will trigger the P0201 code when the resistance or voltage drop at the injector 1 is out of specifications.
VAG Error Code: 1658
EOBD II Error Code: P0204
Fault Location:
Injector 4 (N33) - Circuit Malfunction/Open Circuit
Possible Cause:
Malfunction Indicator Lamp (MIL)(K83) active.
Lack/Loss of Power.
The engine may be harder to start.
Engine hesitation.
Lack/Loss of Power.
The engine may be harder to start.
Engine hesitation.
Wiring/Connector(s).
Injector 4 (N33).
Engine Control Module (ECM).
Engine Control Module (ECM).
Possible Solutions:
Check/Replace all faulty Wiring/Connector(s).
Read Measuring Value Blocks (MVB).
Low side signal current < 2.1 A.
Read Measuring Value Blocks (MVB).
Low side signal current < 2.1 A.
When is the code detected?:
The P0204 is set if the Engine Control Module (ECM) is detects a low or high voltage drop or resistance at the injector 4.
Description:
Engine Control Module (ECM) checks the injectors circuit resistance and monitors the voltage drop during normal operation. The Engine Control Module (ECM) will trigger the P0204 code when the resistance or voltage drop at the injector 4 is out of specifications.
As taken from my https://volkswagenforum.com/forum/ge...oftware-34973/
https://volkswagenforum.com/forum/ne...gnature-34185/
Thread
Thread Starter
Forum
Replies
Last Post
singletrack12
Other Volkswagen Models
3
12-18-2008 10:58 PM
libertyh
Volkswagen Golf
4
04-27-2007 02:47 AM