Accidental short interruption of the engine while driving
#1
Accidental short interruption of the engine while driving
Accidental short interruption of engine operation while driving in a higher gear (4 to 5):
The engine stops accidentally while driving. I Feel the engine jerk.
Since the gear is engaged, the engine starts immediately and continue driving without interruption. The yellow 'Engine' indicator light comes on on the instrument panel. This goes out after some time.
Importent remark: This event occurs considerably more probably when there is less gasoline in tank then the tank half volumen (less then ½ tank volumen).
The engine stops accidentally while driving. I Feel the engine jerk.
Since the gear is engaged, the engine starts immediately and continue driving without interruption. The yellow 'Engine' indicator light comes on on the instrument panel. This goes out after some time.
Importent remark: This event occurs considerably more probably when there is less gasoline in tank then the tank half volumen (less then ½ tank volumen).
#2
Welcome to the forum.
After being prompted.
What were those error codes scanned with a generic scanner if you have posted a picture?
Its not worth searching for those error codes and posting each one.
You need to get your motor scanned (preferably with VAG-COM\VCDS) for any error codes logged in the ecu and post them, that will save a lot of guessing and check systems out.
After being prompted.
What were those error codes scanned with a generic scanner if you have posted a picture?
Its not worth searching for those error codes and posting each one.
You need to get your motor scanned (preferably with VAG-COM\VCDS) for any error codes logged in the ecu and post them, that will save a lot of guessing and check systems out.
#4
If you use VAG-COM\VCDS scanner don't post pictures post the log file in CODE tags?
Manufacturer: VW, Date(s) Used: 10/1997-04/2002, Model: Golf, Engine Code: AZD, 77Kw, 105PS, 1.6 Ltr, 4 Cyls, Remarks: 16v
Manufacturer: VW, Date(s) Used: 10/1997-04/2002, Model: Golf, Engine Code: AZD, 77Kw, 105PS, 1.6 Ltr, 4 Cyls, Remarks: 16v
#5
Dear Keithuk
1) I have finally done the scanning using VAG-COM\VCDS scanner. It was rather difficult to find the VAG … type scanner in the surrounding.
As the description is in the Czech language, I have translated the relevant lines into English as follows:
Translation:
4 errors found
16588 – injector cylinder 4 (N33)
P0204 - 35-10 – error in el. circuit – sporadic
16586 – injector cylinder 2 (N31)
P0202 - 35-10 – error in el. circuit – sporadic
16585 – injector cylinder 1 (N30)
P0201 - 35-10 – error in el. circuit – sporadic
16587 – injector cylinder 3 (N32)
P0203 - 35-10 – error in el. circuit – sporadic
Readiness: 0000 0000
2) I would like to add:
I repeat from my original text dated 08.26.2020:
“Important remark: This event occurs considerably more probably when there is less gasoline in tank then the tank half volumen (less then ½ tank volumen)”
Yours
Zdeno
1) I have finally done the scanning using VAG-COM\VCDS scanner. It was rather difficult to find the VAG … type scanner in the surrounding.
As the description is in the Czech language, I have translated the relevant lines into English as follows:
Translation:
4 errors found
16588 – injector cylinder 4 (N33)
P0204 - 35-10 – error in el. circuit – sporadic
16586 – injector cylinder 2 (N31)
P0202 - 35-10 – error in el. circuit – sporadic
16585 – injector cylinder 1 (N30)
P0201 - 35-10 – error in el. circuit – sporadic
16587 – injector cylinder 3 (N32)
P0203 - 35-10 – error in el. circuit – sporadic
Readiness: 0000 0000
2) I would like to add:
I repeat from my original text dated 08.26.2020:
“Important remark: This event occurs considerably more probably when there is less gasoline in tank then the tank half volumen (less then ½ tank volumen)”
Yours
Zdeno
#6
That isn't an English VCDS log file.
EOBD II Error Code: P0204
Fault Location:
Fuel Injector for Cylinder 4 (N33) Piezoelectric Injector - Circuit Malfunction/Open Circuit
Possible Cause:
Malfunction Indicator Lamp (MIL)(K83) active.
Lack/Loss of Power.
The engine may be harder to start.
Engine hesitation.
Wiring/Connector(s).
Fuel Injector for Cylinder 4 (N33) Piezoelectric Injector.
Engine Control Module (ECM).
Possible Solutions:
Check/Replace all faulty Wiring/Connector(s).
Read Measuring Value Blocks (MVB).
Low side signal current < 2.1 A.
When is the code detected?:
The P0204 is set if the Engine Control Module (ECM) is detects a low or high voltage drop or resistance at the injector 4.
Description:
Engine Control Module (ECM) checks the injectors circuit resistance and monitors the voltage drop during normal operation. The Engine Control Module (ECM) will trigger the P0204 code when the resistance or voltage drop at the injector 4 is out of specifications.
EOBD II Error Code: P0202
Fault Location:
Fuel Injector for Cylinder 2 (N31) Piezoelectric Injector - Circuit Malfunction/Open Circuit
Possible Cause:
Malfunction Indicator Lamp (MIL)(K83) active.
Lack/Loss of Power.
The engine may be harder to start.
Engine hesitation.
Wiring/Connector(s).
Fuel Injector for Cylinder 2 (N31) Piezoelectric Injector.
Engine Control Module (ECM).
Possible Solutions:
Check/Replace all faulty Wiring/Connector(s).
Read Measuring Value Blocks (MVB).
Low side signal current < 2.1 A.
When is the code detected?:
The P0202 is set if the Engine Control Module (ECM) is detects a low or high voltage drop or resistance at the injector 2.
Description:
Engine Control Module (ECM) checks the injectors circuit resistance and monitors the voltage drop during normal operation. The Engine Control Module (ECM) will trigger the P0202 code when the resistance or voltage drop at the injector 2 is out of specifications.
EOBD II Error Code: P0201
Fault Location:
Fuel Injector for Cylinder 1 (N30) Piezoelectric Injector - Circuit Malfunction/Open Circuit
Possible Cause:
Malfunction Indicator Lamp (MIL)(K83) active.
Lack/Loss of Power.
The engine may be harder to start.
Engine hesitation.
Wiring/Connector(s).
Fuel Injector for Cylinder 1 (N30) Piezoelectric Injector.
Engine Control Module (ECM).
Possible Solutions:
Check/Replace all faulty Wiring/Connector(s).
Read Measuring Value Blocks (MVB).
Low side signal current < 2.1 A.
When is the code detected?:
The P0201 is set if the Engine Control Module (ECM) is detects a low or high voltage drop or resistance at the injector 1.
Description:
Engine Control Module (ECM) checks the injectors circuit resistance and monitors the voltage drop during normal operation. The Engine Control Module (ECM) will trigger the P0201 code when the resistance or voltage drop at the injector 1 is out of specifications.
EOBD II Error Code: P0203
Fault Location:
Fuel Injector for Cylinder 3 (N32) Piezoelectric Injector - Circuit Malfunction/Open Circuit
Possible Cause:
Malfunction Indicator Lamp (MIL)(K83) active.
Lack/Loss of Power.
The engine may be harder to start.
Engine hesitation.
Wiring/Connector(s).
Fuel Injector for Cylinder 3 (N32) Piezoelectric Injector.
Engine Control Module (ECM).
Possible Solutions:
Check/Replace all faulty Wiring/Connector(s).
Read Measuring Value Blocks (MVB).
Low side signal current < 2.1 A.
When is the code detected?:
The P0203 is set if the Engine Control Module (ECM) is detects a low or high voltage drop or resistance at the injector 3.
Description:
Engine Control Module (ECM) checks the injectors circuit resistance and monitors the voltage drop during normal operation. The Engine Control Module (ECM) will trigger the P0203 code when the resistance or voltage drop at the injector 3 is out of specifications.
As taken from my new EOBD II Fault Codes Software
VAG Error Code: 16588/9840/000516
EOBD II Error Code: P0204
Fault Location:
Fuel Injector for Cylinder 4 (N33) Piezoelectric Injector - Circuit Malfunction/Open Circuit
Possible Cause:
Malfunction Indicator Lamp (MIL)(K83) active.
Lack/Loss of Power.
The engine may be harder to start.
Engine hesitation.
Wiring/Connector(s).
Fuel Injector for Cylinder 4 (N33) Piezoelectric Injector.
Engine Control Module (ECM).
Possible Solutions:
Check/Replace all faulty Wiring/Connector(s).
Read Measuring Value Blocks (MVB).
Low side signal current < 2.1 A.
When is the code detected?:
The P0204 is set if the Engine Control Module (ECM) is detects a low or high voltage drop or resistance at the injector 4.
Description:
Engine Control Module (ECM) checks the injectors circuit resistance and monitors the voltage drop during normal operation. The Engine Control Module (ECM) will trigger the P0204 code when the resistance or voltage drop at the injector 4 is out of specifications.
VAG Error Code: 16586/000514
EOBD II Error Code: P0202
Fault Location:
Fuel Injector for Cylinder 2 (N31) Piezoelectric Injector - Circuit Malfunction/Open Circuit
Possible Cause:
Malfunction Indicator Lamp (MIL)(K83) active.
Lack/Loss of Power.
The engine may be harder to start.
Engine hesitation.
Wiring/Connector(s).
Fuel Injector for Cylinder 2 (N31) Piezoelectric Injector.
Engine Control Module (ECM).
Possible Solutions:
Check/Replace all faulty Wiring/Connector(s).
Read Measuring Value Blocks (MVB).
Low side signal current < 2.1 A.
When is the code detected?:
The P0202 is set if the Engine Control Module (ECM) is detects a low or high voltage drop or resistance at the injector 2.
Description:
Engine Control Module (ECM) checks the injectors circuit resistance and monitors the voltage drop during normal operation. The Engine Control Module (ECM) will trigger the P0202 code when the resistance or voltage drop at the injector 2 is out of specifications.
VAG Error Code: 16585/15887/000513
EOBD II Error Code: P0201
Fault Location:
Fuel Injector for Cylinder 1 (N30) Piezoelectric Injector - Circuit Malfunction/Open Circuit
Possible Cause:
Malfunction Indicator Lamp (MIL)(K83) active.
Lack/Loss of Power.
The engine may be harder to start.
Engine hesitation.
Wiring/Connector(s).
Fuel Injector for Cylinder 1 (N30) Piezoelectric Injector.
Engine Control Module (ECM).
Possible Solutions:
Check/Replace all faulty Wiring/Connector(s).
Read Measuring Value Blocks (MVB).
Low side signal current < 2.1 A.
When is the code detected?:
The P0201 is set if the Engine Control Module (ECM) is detects a low or high voltage drop or resistance at the injector 1.
Description:
Engine Control Module (ECM) checks the injectors circuit resistance and monitors the voltage drop during normal operation. The Engine Control Module (ECM) will trigger the P0201 code when the resistance or voltage drop at the injector 1 is out of specifications.
VAG Error Code: 16587/9835/9839/000515
EOBD II Error Code: P0203
Fault Location:
Fuel Injector for Cylinder 3 (N32) Piezoelectric Injector - Circuit Malfunction/Open Circuit
Possible Cause:
Malfunction Indicator Lamp (MIL)(K83) active.
Lack/Loss of Power.
The engine may be harder to start.
Engine hesitation.
Wiring/Connector(s).
Fuel Injector for Cylinder 3 (N32) Piezoelectric Injector.
Engine Control Module (ECM).
Possible Solutions:
Check/Replace all faulty Wiring/Connector(s).
Read Measuring Value Blocks (MVB).
Low side signal current < 2.1 A.
When is the code detected?:
The P0203 is set if the Engine Control Module (ECM) is detects a low or high voltage drop or resistance at the injector 3.
Description:
Engine Control Module (ECM) checks the injectors circuit resistance and monitors the voltage drop during normal operation. The Engine Control Module (ECM) will trigger the P0203 code when the resistance or voltage drop at the injector 3 is out of specifications.
As taken from my new EOBD II Fault Codes Software
Thread
Thread Starter
Forum
Replies
Last Post
vwparts1
PRIVATE For Sale / Trade Classifieds
0
07-26-2011 09:18 PM